THE ESC MADE FOR DRIFTERS

The SLYDR Brushless Drift ESC is compatible with all three Drift-Spec Brushless Motors (#3466-3468)(별매)

With input from the top drifters of the world, Novak has developed the SLYDR Brushless Drift ESC (#1712). This SLYDR Drift ESC, which is based on Novak’s GTB, contains new brake adjustments and features to help fine tune brake response, as well as all new throttle curve adjustments to further customize the already-smooth throttle response.

SLYDR DRIFT BRUSHLESS ESC
Though the SLYDR Brushless Drift ESC has one throttle profile, the drift-specific ESC is completely programmable and packed with nine customizable parameters. Novak’s new Throttle Curve gives drivers the ability to experiment with three throttle responses – Linear, Expo-1 and Expo-2 – which range between a quick burst of power to a smoother, more controlled low-end power delivery. In addition, the SLYDR’s Brake Frequency adjustment contains seven degrees of adjustability from a smooth and controllable brake to a more abrupt and grabbier feel. The dozens of adjustments allow drivers to fine-tune their vehicle’s throttle braking for better control and advanced drifting.

But the customization doesn’t end with braking. Novak has also built into the ESC Li-Po Cut-Off Circuitry that prevents the batteries from going below the critical safety voltage level and a Motor Rotation feature that allows the user to easily select direction of the motor.

This SLYDR ESC can be factory wired to one of three Drift-Spec Brushless Motors (#3466-3468) to create the SLYDR Brushless Drift System (#3066-3068).

Please Note: The SLYDR Brushless ESC is not only for the Drift Crowd. It can be used just like the GTB ESC for nearly all applications. Due to the higher brake settings that are available in the SLYDR, we recommend following the SLYDR’s 5.5-turn motor limit to avoid damage. Beyond this requirement, the internals of the SLYDR are similar to the GTB in the brushless mode. Some drivers have found the new brake adjustment features found in the SLYDR to be very useful for fine tuning feel and response. This has been beneficial in applications where fine control and minor brake input changes are used, such as off-road and on-road racing.

SLYDR BRUSHLESS DRIFT ESC FEATURES Fully programmable throttle profile specifically developed for drifting Nine adjustable parameters: Minimum Brake (10 settings from 3-50%), Drag Brake (10 settings from 3-50%), Dead Band (5 settings from 2-6%), Minimum Drive (5 settings from 2-12%), Throttle Curve (Linear, Expo-1 and Expo-2), Brake Frequency (7 settings from 1-8 kHz), Reverse, Motor Rotation and Li-Po Cut-Off User-friendly interface and 4 different color status LEDs. User can fine-tune one parameter at a time without having to re-enter other parameters Based on the Novak GTB Brushless ESC for ultimate brushless motor performance Built-in Smart-Stop Li-Po Cut-Off Circuitry Protection to monitor battery voltage level Independent programming of Drag Brakes and Minimum Brake for the ultimate braking control One-Touch Set-Up for quick, easy transmitter setup Smart Braking II enables users to "shift" from forward to reverse Compatible with Novak’s 540-size sensored brushless motors down to 5.5 turns Microprocessor-controlled Gold-Plated PCB Direct-Solder Wiring Tabs User-replaceable input harness (#5315) and remote power programming switch (#5602) 30x30x6mm cooling fan (#5648) mounted on factory-installed heat sink Factory-installed Power Trans-Cap Module (#5679) for cooler operating temperatures Water-resistant case Locked Rotor Detection and Thermal Overload Protection Novak’s Radio-Priority and Polar Drive Circuits Meets RoHS compliance and includes 120-Day Warranty Designed and assembled by Novak in Irvine, California, using globally-sourced components

SLYDR BRUSHLESS DRIFT ESC SPECS Input Voltage: 2S Li-Po cells or 4-6 NiMH cells (1.2V/cell) Footprint: 1.16” x 1.49” (29.5 x 37.8 mm) Weight (without wires): 1.36 oz. (38.5 g) Motor Limit: 5.5-turn Novak 540-size sensored brushless motor On-Resistance: 0.00040 ohms @ 25°C trans. temp. BEC: 6.0 volts DC / 3.0 amps Status LEDs: 4 Voltage Cut-Off: 6.25V (when Li-Poly Cut-Off Circuitry is enabled) Power Wires (battery/motor): 14G Super-Flex Copper-Strand Silicone Wire